RAID5 Patches

Notes about RAID5 Internals

Structures

In Linux, RAID5 handles all incoming requests by small units called stripes. A stripe is a set of blocks taken from all disks at the same position. A block is defined as a unit of PAGE_SIZE bytes.

For example, suppose you have 3 disks and have specified 8K chunksize. Internally, RAID5 will look like this:

	S0	S8	S32	S40
Disk1	#0	#8	#32	#40
Disk2	#16	#24	#48	#56
Disk3	P0	P8	P32	P40

where:

• Sn -- Number of internal stripe
• #n -- An offset in sectors (512bytes)
• Pn -- Parity for other blocks in the stripe (actually, it floats among disks)

As you can see, an 8K chunksize means 2 contiguous blocks.

Logic

make_request() goes through an incoming request, breaking it into blocks (PAGE_SIZE) and handling them separately. Given bio with bi_sector = 0 bi_size = 24K and the array described above, make_request() would handle #0,#8 and #16.

For every block, add_stripe_bio() and handle_stripe() are called.

add_stripe_bio() the intention is to add bio to a given stripe. Later, in handle_stripe(), we will be able to use bio and its data for serving requests.

handle_stripe() is a core of RAID5 (as discussed in the next section).

handle_stripe()

The routine works with a stripe. It checks what should be done, learns the current state of a stripe in the internal cache, decides what I/O is needed to satisfy user requests, and does recovery.

For example, if a user wants to write block #0 (8 sectors starting from sector 0), RAID5's responsibility is to store new data and update parity P0. There are a few possibilities here:

1. delay serving until the data for block #16 is ready -- probably the user will want to write #16 very soon?
2. read #16, make a new parity P0; write #0 and P0.
3. read P0, roll back the old #0 from P0 (so it looks like we did parity with #0) and re-compute parity with the new #0.

The first possibility looks like the best option because it does not require a very expensive read, but the problem is that user may need to write only #0 and not #16 in near future.

Also, the queue can get unplugged, meaning that the user wants all requests to complete. (Unfortunately, in the current block layer, there is no way to specify the exact request that the user is interested in, so any completion interest means immediate serving of the entire queue).

Problems

This is a short list of RAID5 problems that we encountered in the Thumper project:

* Order of handling is not good for large requests

  As handle_stripe() goes in logical block order, it
  handles S0, then S8, and then again S0 and S8. After the first touch, 
  S0 is left with block #0 up-to-date, while #16 and P0 are not. Thus, 
  if the stripe is forced for completion, we would need to read block
  #16 or P0 to get a fully up-to-date stripe. Such reads hurt throughput
  almost to death. If just a single process writes, then things are
  OK, because nobody unplugs the queue, and there are no requests to
  force completion of a pending request. But, if there are more writers, then
  a queue unplug often occurs, and pending requests are often forced
  for completion. Take into account, that in reality, we use a large
  chuck size (128K, 256K and even larger). Hence, in the end, there 
  are many out-of-date stripes in the cache and many reads.

* memcpy() is a top consumer

  All requests go via internal cache, on dual-core, two-way Opteron. 
  It takes up to 30-33% of CPU doing 1 GB/s writes.

* Small requests

  To fill I/O pipes and reach good throughput, we need very large
  I/O requests. Lustre does this by using a bio subsystem on 2.6. But, as 
  described above, RAID5 handles all blocks separately and
  issues separate I/O (bio) for every block. This is partially solved 
  by an I/O scheduler that merges small requests into bigger ones. But, 
  due to the nature of the block subsystem, any process that wants I/O to
  get completed unplugs the queue, and we can get many small requests
  in the pipe.

We have developed patches that address the described problems. You can find them at ftp://ftp.clusterfs.com/pub/people/alex/raid5